Software • ADALM-Pluto • HAM-to-HAM SSH/HTTP diagnostics

Pluto Probe

A lightweight utility to quickly figure out how to connect to your Pluto the right way: it checks SSH/HTTP, tries the available methods, and tells you whether it’s better to use Paramiko or system SSH (ssh.exe) — with clear, user-friendly “next steps”.

I wrote it after running into a real case: some “custom” firmwares (e.g. Dropbear / PlutoDVB / F5OEO) may respond to SSH, yet be unstable with Paramiko — especially when the Pluto is connected via USB (a typical scenario is the USB interface at 192.168.2.1 with F5OEO firmware). PlutoProbe saves you hours of trial and error and points you to the most reliable method for diagnostics (and for Pluto Status Monitor), when simply entering user “root” and password “analog” in Pluto Status Monitor seems to not work at all.

Practical tip: if you change firmware and SSH starts acting weird, often this fixes it: ssh-keygen -R <IP>.

Related tool

PlutoProbe can also be used as a “pre-check” for Pluto Status Monitor (same connection logic).

Go to Pluto Status Monitor →
Quick facts
  • Goal: SSH/HTTP diagnostics + recommended connection method
  • Output: TXT and JSON reports (save/copy)
  • OS: Windows 10/11 (64-bit)
  • Methods: Paramiko + system SSH (ssh.exe) + agent/keys
  • Typical use: ADI stock firmware / custom firmware (Dropbear, F5OEO, etc.)
PlutoProbe — main window (SSH/HTTP Diagnostic)

Simple workflow: enter the IP, optionally choose keys/agent, then click Analyze.

What it is for in practice

PlutoProbe answers a concrete question: “With this firmware, what’s the most reliable way to run SSH diagnostics?” In many cases Paramiko works perfectly; in others (custom firmware) it may fail even though SSH is reachable.

The tool tries the available methods on a best-effort basis, collects fingerprints (SSH banner, HTTP title, uname, etc.), and produces a clear report with a recommended method and suggested actions (e.g. cleaning known_hosts).

How it works

1Detection (SSH/HTTP)

Checks whether SSH responds and reads useful clues from the banner. If available, it also probes HTTP for a quick fingerprint.

2Method testing

Tries Paramiko (Python) and, when needed, falls back to system SSH (ssh.exe) to clarify edge cases (Dropbear, host key mismatch, etc.).

3Report + next steps

Produces a readable TXT report and a technical JSON report. It tells you what to do next—without a wall of logs.

Typical scenarios

Scenario A — ADI firmware / Paramiko OK

PlutoProbe confirms Paramiko compatibility and suggests using the same parameters in Pluto Status Monitor.

  • SSH session completes successfully
  • Recommended method: Paramiko
  • Common tip: ssh-keygen -R <IP> after a firmware change

Scenario B — Custom firmware / Paramiko unstable

SSH is reachable, but Paramiko cannot complete the session. PlutoProbe recommends system SSH as the best method for clearer diagnostics.

  • Recommended method: system SSH (ssh.exe)
  • Non-technical explanation: it’s not your PC’s fault
  • Suggested steps: clean up known_hosts + re-test
  • FYI: with F5OEO firmware and the Pluto connected in USB mode, SSH may not be reachable from Pluto Status Monitor. The simplest workaround is to use a USB → Ethernet adapter on the USB port (the Pluto becomes reachable over the network). This does not occur with ADI stock firmware (0.37, 0.38, 0.39).

Screenshots / Visual guide

Note: in many cases, running ssh-keygen -R <IP> after a firmware swap, then re-running the analysis, is enough to fix SSH issues.

What it does NOT do (by design)

PlutoProbe is intentionally lightweight: it is not a full SSH client and does not aim to replace advanced tools. It’s a diagnostic helper that guides you to the right method and produces a clean report.

  • It does not modify Pluto firmware or configuration.
  • It does not promise 100% compatibility with every fork/firmware out there.
  • It cannot “fix” firewall/routing problems.
  • It is not an SDR tool (it does not replace SDR Console).
  • It does not control station hardware (PTT/PA/rotators/etc.).
  • It does not send data to third parties: reports stay local.

Download and notes

PlutoProbe is distributed as a portable ZIP. Download, extract, run. If you use it together with Pluto Status Monitor, consider it a quick “pre-check” after a firmware change or whenever SSH behaves unexpectedly.

Tip: when troubleshooting, always save the JSON report too—it makes it easy to compare different setups cleanly.